Joiner in Wrocław, solid wood furniture made to measure
ul. Lotnicza 000, Wrocław · workshop Mon-Fri 7-16 · shop Sat 8-13
Tables, bookcases, worktops and stairs in oak, ash, beech and walnut. Measuring visits in Wrocław are free, and you see the price before you call.
Draw your furniture. The price fills in the title block.
Ask a joiner “how much will it cost” and the usual answer is “give us a call”. Here you drag a dimension line and the drawing's title block fills in the species, a price range and the lead time. We start the conversation after the measuring visit from the same numbers.
Drag the rust circles on the dimension lines. With a keyboard: Tab, then the arrow keys (with Shift in 10 cm steps).
Guide prices
Including timber, three coats of oil, delivery and fitting in Wrocław. We put the exact price in writing within 5 working days of the measuring visit.
| Piece | Price | Lead time |
|---|---|---|
| Oak table 200 × 90 cm, 40 mm top | PLN 5,100-6,400 | 6-8 weeks |
| Ash table 180 × 90 cm, 40 mm top | PLN 4,600-5,800 | 6-8 weeks |
| Walnut table 220 × 100 cm, 40 mm top | PLN 7,400-9,200 | 7-9 weeks |
| Oak bookcase 120 × 200 × 32 cm | PLN 5,600-7,000 | 5-7 weeks |
| Oak kitchen worktop 240 × 64 cm, 40 mm | PLN 1,900-2,400 | 2-3 weeks |
| Stairs: oak cladding on concrete, per step | from PLN 650 | 4-6 weeks |
| Kitchen with solid wood fronts, per running metre | from PLN 3,900 | 8-10 weeks |
Cutting listPP-01
A price counted in boards.
Instead of a “custom quote”: we turn the drawing into a cutting list, the same one we use in the workshop. Every part gets an allowance for planing, and the saw kerf sits between parts.
| Item | Part | Qty | L × W × T [mm] |
|---|---|---|---|
| A | Top stave | 10 | 2000 × 90 × 40 |
| B | Leg | 4 | 710 × 80 × 80 |
| C | Apron, long | 2 | 1760 × 100 × 25 |
| D | Apron, short | 2 | 660 × 100 × 25 |
Staves run the full length of the top, with no finger joints. Allowance 30 mm on length and 6 mm on width, saw kerf 4 mm.
The cutting list follows the drawing above.
We make chopping boards from the offcuts. They are in the shop.
One log, three different boards.
How a tabletop looks depends on how the saw went through the log. Move the cutting line across the log section and you will see the face of the board it gives.
Log end, Ø 50 cm. Board 52 mm, kerf 4 mm.
Board face, 150 cm of its length
Flat sawn
- Board width
- 41 cm
- Rings to face
- 20°
- Timber price
- no surcharge
- Flat sawn
- A board from the side of the log. The rings form arches, known as cathedrals. A log gives the most of these, so they are the cheapest. They move the most across the width.
- Rift sawn
- Between the side and the centre. The rings run diagonally and the figure is calm and even. Good for table legs, as they look the same from every side.
- Quarter sawn
- A board through the centre of the log. Straight, tight rings, and in oak the shimmer of medullary rays, known as ray fleck. It moves the least, a log gives the fewest, and the timber costs 30% more.
The cut you choose is written into the drawing's title block.
- Oak Hard and heavy, with a clear grain. For tables, stairs and worktops. Timber from Silesia and Greater Poland.
- Ash Pale and springy, with a strong grain figure. Cheaper than oak and great for tables and chairs.
- Beech Even, slightly pink, the cheapest of the hardwoods. It does not like moisture, so we do not use it for worktops by the sink.
- American walnut Dark and chocolatey, with pale sapwood at the edge. We order it in for each job, so the lead time is a week longer.
From measuring to fitting: eight weeks on a folding rule.
Click a week on the rule and we will mark what happens to your furniture then. A table takes us 6-8 weeks, a kitchen worktop 2-3.
- Measuring visitweek 1
We come with a tape measure and timber samples. Free in Wrocław, PLN 60 up to 30 km outside the city, deducted from the order.
- Drawing and price in writingweek 1-2
Within 5 working days you get a three-view drawing and the price. The 30% deposit comes only after you approve it.
- The timber acclimatisesweek 2-3
The boards rest in a workshop heated like a flat until the moisture drops to 8-10%. We write the moisture meter reading on the order card.
- Joineryweek 3-6
We plane, glue up the staves and cut mortise and tenon joints. Every week we text you a photo from the workshop.
- Oilweek 6-7
Three coats of hardwax oil. Each dries for a day, with a 240 grit sanding in between.
- Delivery and fittingweek 7-8
We deliver, assemble and level. Fitting a kitchen or stairs takes 1 to 3 days.
Our work
Under every photo: what the piece is made of, its size and which part of Wrocław it lives in.
The workshop shop: boards, worktops and oils.
The same boards we make furniture from. Kiln dried to 8-10%, cut to size while you wait. Pick up on Saturday 8-13 or on weekdays by phone. Set something aside and we add it to your order card.
-
Planed oak board
- Size
- 2000 × 180 × 40 mm
- Moisture
- 8-10%
- Grade
- A/B, no loose knots
PLN 189
-
Planed ash board
- Size
- 2000 × 180 × 26 mm
- Moisture
- 8-10%
- Grade
- A/B
PLN 99
-
Glued oak worktop
- Size
- 640 mm deep, 40 mm thick, up to 4 m long
- Staves
- full length, no finger joints
- Cutting
- PLN 15 per cut
from PLN 790 per running metre
-
Offcut chopping board
- Timber
- oak or walnut, offcuts from our furniture
- Size
- from 350 × 200 to 500 × 250 mm
- Finish
- food-safe oil
PLN 120-190 each one different
-
Hardwax oil
0.75 l, covers about 18 m² per coat. We use it on tables and bookcases.
PLN 149
-
Kitchen worktop oil
0.5 l, resistant to water and grease. For refreshing a worktop once a year.
PLN 89
-
Services on site
Cutting to size PLN 15 per cut, planing PLN 20 per running metre, edge routing from PLN 30.
Order card.
We get back to you within one working day to book the measuring visit. Your drawing and anything set aside in the shop are added automatically.
Pith & Plane, joinery and timber shop
ul. Lotnicza 000, 54-000 Wrocław
- Workshop and office
- Mon-Fri 7:00-16:00
- Timber shop
- Sat 8:00-13:00, weekdays by phone
Drive in through the courtyard gate, parking by the workshop. We load boards into your car and deliver anything longer than 3 m for PLN 80.